How to Check If Tesla has Garage Door Opener and How to Program It

By Nuno Cristovao

Teslas have the ability to automatically open your garage door as you’re approaching your home. They can also automatically close it as you’re leaving.

They do this by combining the GPS signal with the HomeLink module that opens your garage door.

Tesla Garage Door Opener with HomeLink

How to Tell If Your Tesla Has HomeLink

All Teslas are capable of opening garage doors using HomeLink, however not every Tesla comes equipped with the HomeLink module.

If you have a Model S or Model X, then your car already has the capability to open your garage door.

If you have another model, then whether it’s included in your car will vary. Model 3s included HomeLink only up until Spring of 2019. It then became an option that would be installed after delivery through Tesla service. All Model Ys do not have it installed unless it was installed after delivery.

However, the easiest way to tell if your car has a garage door opener is to check on the car’s display. You can go to Controls > Software then tap on Additional Vehicle Information.

This will bring up a screen that will display several important details about your vehicle and the hardware it includes.

The screen will display which full self-driving computer hardware is installed, your infotainment processor and more. It will also display whether you have the HomeLink garage door opener hardware installed.

Next to ‘Garage door opener’, you will either see ‘Not installed,’ or ‘HomeLink 5 (Opt 2).’ The number may vary, but it will mean that you have the HomeLink module installed and your car is capable of opening garage doors.

Program HomeLink Garage Door Opener

If you have a garage door opener in your Tesla, then you can program the car to automatically open the garage door when you pull up to the house.

You can also operate the doors individually through the car’s interface and even operate the main garage door through the Tesla app.

To program your car you’ll need the remote that came with your garage door opener, or easy access to the garage door motor in your garage.

If you’re programming the car using the button on the garage door opener motor, make sure you have plenty of space and a good step ladder because you’ll need to complete the operation in a certain amount of time. If someone is available to help, that will make the process much easier.

To get started you’ll tap on the HomeLink icon along the top of your Tesla’s screen that looks like a house with an arrow then tap HomeLink Settings.

This brings up the HomeLink screen which allows you to add various garage doors or compatible accessories such as lights or gates.

Start by tapping on Add New HomeLink then enter a name for this garage door, such as ‘Left Garage’ and then tap Create HomeLink.

Standard Mode or D-Mode

You’ll next be presented to set the HomeLink transmit mode. The mode you need to pick will depend on your location and method you’re using to program your car.

Standard Mode - This is the most common mode. If you’re unsure of which to use, you should start with this one, as it’s the simplest to set up. This option requires the use of your garage door remote.

D-Mode - D-mode is usually used in North America. You’ll want to use D-mode if you’re using the ‘Learn’ or ‘Smart’ button on your garage door opener motor.

UR-Mode - UR-mode is similar to D-mode but it’s a standard that’s usually found in Europe, the Middle East and Asia. It’ll also require you to use the ‘Learn’ button on your garage door opener motor.

Set your preferred mode and tap Set Mode.

Next, you’ll want to make sure your car is parked in front of your garage. The car uses this location to determine when to open your garage door when arriving home.

Later you’ll then be able to set how many feet before reaching this location should the car send the signal to open your garage.

Programming With Standard Mode

Get ready to program your car and tap Start. You’ll now want to go outside of your car with your garage door remote and point it at the front bumper closer to the passenger side.

Now press and hold the button that opens your garage door on the remote and keep it pressed. It can take up to 30 seconds to program. Your car’s lights will flash when it’s complete. Keep in mind that your garage door will open or close when you do this, so make sure there is nothing in the way.

Once you see your headlights flash, that means the car was successfully able to record the signal from your remote.

When you go back in your vehicle you should see that the recording was completed and you’re prompted to tap next to continue.

If you’re using Standard Mode, the next step will vary depending on whether your remote is QuickTrain compatible or not.

If your remote is QuickTrain compatible or doesn’t use a rolling code then you can tap Continue, if it’s not either of those, then you’ll be required to press the ‘Learn’ button on your garage door opener motor.

If you’re not sure, you can try pressing continue and see if HomeLink works. If it doesn’t work then you know your remote is not QuickTrain compatible.

Programming With D-Mode or UR-Mode

If you’re using D-Mode or UR-Mode to program your car you will need easy access to the garage door opener motor.

The car will ask you to press the Learn or Smart button on the garage door motor. It’ll be a small button that may be behind a cover or door. It’s usually a bright color such as orange, red, yellow or purple, but it can be any color.

After pressing the button you will need to go back to the car in a short period of time and tap continue. This is to prevent unauthorized use of your garage door.

Testing the Button

After programming your garage door the car will ask you to test it.

The car will have you test the garage door button in the car to see if it works and you’ll be given a chance to go back and choose a different option if it didn’t work the first time.

Once you have your garage doors opening from the car and tap save, you can set various options for the garage door.

Auto Fold Mirrors

This option will cause your car to fold its mirrors right before arriving at your garage. Keep in mind this may make backing out of your garage a little more difficult. Only use this option if you need to.

Auto Open When Arriving

Teslas will combine your GPS signal with your HomeLink transmitter and auto open your garage doors as you’re approaching your house.

This is a really convenient feature and I’d recommend having it on as long as your garage door has the safety sensors at the bottom that will prevent it from closing if anything is in the way.

You can also choose the number of feet away from your garage when the car should send the signal to open it.

It’s nice to have your garage door fully open before you get to it so that you don’t need to stop and wait. However, the number of feet that is right for you will depend on your garage door opener and how far away it could receive a signal.

I’d also recommend having your garage door in view so that for those rare times when you come home and the garage door is already open. This will cause your car to send another ‘open’ signal, causing your garage door to start closing.

It's important to understand that the car has no way to know whether your garage door is open or closed, and unfortunately HomeLink simply sends an "open/close" signal, which causes the garage door to open if it’s closed or close if it’s opened. Some caution is necessary, but the feature works well, especially when you’re arriving home.

Tesla recommends only using the auto-open or auto-close features when your garage door is installed with safety sensors along the bottom.

Keep in mind that the car determines the location of your garage door based on where your car was when you programmed the garage door. The location can be reset at any time.

Auto Close When Leaving

This is the opposite of ‘Auto Open when Arriving’. Your car will automatically send a signal to close your garage door when you’re leaving home.

We do need to be cautious with these features as they’re not discrete open and close signals and they just tell the garage door to switch position.

Reset Location

If you weren’t in front of your garage door when you programmed it, then your car has the wrong location for your garage door. Choosing ‘reset location’ when in front of your garage door will cause the car to change the location of your garage to its current position.

You’ll need to do this for each garage door.

Chime for Auto-Open and Auto-Close

On the HomeLink settings screen you can also set whether you’d like the car to chime before auto opening or auto closing the garage door.

This will have the car make a short ding sound before auto opening or auto closing your garage doors. It’s a little reminder that the garage door is open to move. It also gives you a chance to cancel the auto opening or auto closing procedure before it starts. You’ll see the HomeLink menu come up with a cancel button when this happens.

Limited to 3 Garages or Devices

The HomeLink module that Tesla uses is limited to three HomeLink devices. Unfortunately, this is a limitation of the module itself and not something that Tesla can change.

Add or Install Garage Door Opener in Your Tesla

If you have a Tesla Model 3 or Model Y that does not have the garage door opener, then you can purchase it separately directly from Tesla.

Unfortunately, it can’t be purchased when you buy the car and it needs to be bought and installed by Tesla service after delivery.

The cost for the parts and installation are $325.

If Tesla offers mobile service in your area then it's a convenient and painless process.

Set Which Garage Door Opens In App

In the Tesla app there is a HomeLink icon that will open your garage door. Unfortunately, this button can only be assigned to one garage door.

There is no way to have your Tesla open the other garage doors programmed in the vehicle, however you can pick which garage door to open when you press the HomeLink icon in the Tesla app.

The following procedure requires you to have Enhanced Autopilot (EAP) or FSD. If you go in your car and go to Controls > Autopilot then tap on Summon you’ll be presented with Summon details.

To choose your garage door, tap HomeLink then pick your garage door. You can then turn HomeLink off again. Keep in mind that if you use Summon with HomeLink enabled then you are telling the car which garage door to open before backing out of the garage.

If you do not have EAP or FSD, then you may have to change the order of your garage doors in order to change the one that opens when pressing the HomeLink icon.

Ordering a New Tesla?

Consider using our referral code (nuno84363) to get up to $2,000 off your new Tesla and get 3 Months of FSD for free.

Tesla FSD V13.2.2 Arrives With Holiday Update Features; Rolling out to HW4 Models

By Karan Singh
Not a Tesla App

FSD users can now join in the Holiday revelry, as FSDS V13.2.2 has started rolling out to customers, and it includes all the 2024 Telsa Holiday Update features.

Tesla’s VP of AI - Ashok Elluswamy, previously mentioned that the Holiday Update would be making its way to FSD users sometime this week. Ashok’s timelines have been right on point. All models with AI4/HW4 vehicles in North America are starting to receive the updated FSD release alongside all the features of the Holiday update.

This new build is update 2024.45.25.5, which should make its way throughout the fleet over the week.

Holiday Highlights

The Holiday update has a ton of new features in it, including new app features like Apple Watch support, the Dashcam and Sentry Mode Viewer and the ability to start Light Shows.

We also received rear cross-traffic alerts, while navigation received Search Along Route, Arrival Energy at Destination and Weather at Destination, and Precipitation Maps.

On the entertainment side, the Holiday Update brings the SiriusXM streaming app to the Model 3, Model Y, and Cybertruck, as well as an updated TuneIn player. Of course, there are new Cybertruck-specific features such as custom Cybertruck Wraps (don’t worry it’s coming to all models), a new Cyber Santa Mode, and Santa and Rainbow Road ambient lighting support.

Video of FSD V13.2.2

Here is our first look at FSD V13.2.2. While the release notes don’t point out any new features for FSD, it’s expected to include several unknown fixes and improvements.

Already on the Holiday Update?

If you’re already on Tesla’s Holiday update, version 2024.44.25.2, and you have a HW4 vehicle, then this version now qualifies you to receive FSD V13.2. We expect all HW4 vehicles with FSD to migrate to this version in the coming week or two.

Update 2024.45.25.5

FSD Supervised 13.2.2
Installed on 4.2% of fleet
399 Installs today
Last updated: Dec 23, 1:55 pm UTC

If you have HW3, then look out for a future update, including FSD v12.6.

FSD V12.6 for HW3 Soon

For Hardware 3 owners, FSD V12.6 is also right around the corner - it should be launching no later than the end of the year, according to Ashok. We’re expecting the new tech stack for highway driving, the updated speed profiles, including Hurry Mode, as well as improvements from V12.5.6 to land for HW3 soon.

If you’re excited about that, go read our in-depth look at V12.5.6 to see a preview of what you’ll be getting in V12.6.

We’re looking forward to seeing the demo drives of V13.2.2 from some of our usual influencers, but the good news is the update has already started rolling out to the general public, so expect larger waves soon.

Tesla Referral Code - Get Up to $2,000 Off a New Tesla

By Not a Tesla App Staff
Not a Tesla App

If you’re planning to buy a new Tesla, consider using our referral code. Not only will you receive up to $2,000 off your vehicle, but you’ll help support our site.

Plus, if you take delivery by December 31st, you’ll also get 3 months of free Supercharging and Full Self-Driving (FSD).

Discount Per Model

  • Model Y - $1,000 off

  • Model 3 - $1,500 off

  • Model S, Model X or Cybertruck - $2,000 off

Free Supercharging and FSD

You must take delivery by December 31st, 2024 to qualify for the three months of FSD and free Supercharging. It’s not clear whether Tesla will offer these benefits starting January 1st.

Referral Codes

All referral codes will give you the same benefits. However, each one is limited to 10 uses, so if one hits the limit, try another one.

Nuno84363

Karan29050

Latest Tesla Update

Confirmed by Elon

Take a look at features that Elon Musk has said will be coming soon.

More Tesla News

Tesla Videos

Latest Tesla Update

Confirmed by Elon

Take a look at features that Elon Musk has said will be coming soon.

Subscribe

Subscribe to our weekly newsletter